SSM24 新一代弹性防水涂层
SSM24 New generation of elastic waterproof coating
一、产品介绍Product introduction
SSM24 新一代弹性防水涂层是德国Drache Handels UG 公司于二十一世纪研发的一种以单组份环保型水性高分子聚合物树脂为主要原料，通过科学工艺生产精制而成，涂料涂层致密、与各类基材附着力强，封闭性能和抗渗性能优良，遮盖力好，具有优异的耐老化性能，户外长期使用不脱落、不粉化、不变色，对建筑物表面具有优异防水保护作用，在欧美地区应用广泛。
SSM24 New generation of elastic waterproof coating is a German Drache Handels UG company in the 21st century research and development of a single-component environmental protection water-based polymer resin as the main raw material, through scientific process production refined, dense coating, strong adhesion to various substrates, sealing performance and impermeability, good covering power. It has excellent aging resistance, outdoor long-term use does not fall off, does not powder, does not change color, has excellent waterproof protection on the surface of the building, and is widely used in Europe and the United States.
二、产品特性Product characteristics
♦ 涂膜密实，粘结性好，一体成型防水体系
♦ 优异的耐老化性能，户外长期使用不脱落、不粉化、不变色，超长使用寿命。
♦ 优良的低温柔性，-40°不开裂。
♦ 良好的耐酸、耐碱、防腐性能。
♦ 优异的防水、防霉性能。
♦ 环保水性涂料，对环境无污染，无毒性成分，使用安全。
♦ 施工方便，是焦油型聚氨酯防水涂料的更新换代产品。
♦ The film is dense, good adhesion, one body forming waterproof system
♦ Excellent aging resistance, outdoor long-term use does not fall off, does not powder, does not change color, long service life.
♦ Excellent low temperature flexibility, -40° no cracking.
♦ Good acid resistance, alkali resistance, corrosion resistance.
♦ Excellent water and mildew resistance.
♦ Environmental protection waterborne paint, no pollution to the environment, non-toxic ingredients, safe to use.
♦ Easy to construct, it is the replacement product of tar-type polyurethane waterproof coating.
三、产品应用范围Product application range
混凝土屋面、钢结构屋面、厨房卫生间地面、浴室、蓄水池、地下室、防水卷材SBS及旧屋面的防水和翻新等工程（如沥青、PVC、SBS、聚氨酯等各种基面）。
Concrete roof, steel structure roof, kitchen toilet floor, bathroom, reservoir, basement, waterproof coil SBS and old roof waterproof and renovation projects (such as asphalt, PVC, SBS, polyurethane and other bases).
四、技术参数Technical parameter
产品物理属性Physical property of product
|
项目 |
结果 |
|
外观 |
白色或灰色 |
|
光泽 |
哑光 |
|
比重（g/cm3 ） |
1.12 |
|
粘度(cps )@20℃ |
420 |
|
固含量（%） |
71%±2% |
|
表干时间（小时） |
夏天：1-2小时 冬天：2-4小时 |
|
理论涂布率 |
0.17kg/m2(厚度100um) |
典型物理测试性能Typical physical test performance
|
项目 |
测试标准 |
结果 |
|
遮盖力（白色或浅色a）/(g/m²) |
JG/T235-2008 |
≤150 |
|
干燥时间/h |
JG/T172-2005 |
表干≤2； 实干≤24 |
|
附着力（划格法）/级 |
JG/T172-2005 |
≤1 |
|
不透水性 |
JG/T172-2005 |
0.3MPa/30min不透水 |
|
耐冲击性/cm |
JG/T172-2005 |
≥30 |
|
拉伸强度 |
JG/T172-2005 |
≥1.7Mpa |
|
断裂伸长率 |
JG/T172-2005 |
≥200%（加胎体后视胎体延伸率） |
|
抗撕裂，≥kN/m |
JG/T172-2005 |
35 |
|
涂层耐温变性（5次循环） |
JG/T172-2005 |
无异常 |
耐腐蚀性能Corrosion resistance
|
耐酸性c（5%H2SO4） |
JG/T172-2005 |
168 h无异常 |
|
耐盐雾 |
JG/T172-2005 |
1000 h不起泡、不脱落 |
|
人工加速老化处理（1000h） |
拉伸强度保持率，% |
85 |
|
断裂延伸率，% |
≥150 |
产品相应固化时间Product curing time
|
基材温度 |
表干 |
步行强度 |
完全固化 |
|
+10℃ |
3h |
16h |
7d |
|
+20℃ |
1h |
10h |
7d |
|
+30℃ |
0.5h |
6h |
7d |
注意：固化时间会因环境情况的变化而有所不同，尤其是温度和相对湿度的变化。
Note: Curing times vary depending on environmental conditions, especially temperature and relative humidity.
五、施工注意事项Construction precautions
♦ 施工应用指导
推荐干膜厚度：200-300um
覆涂间隔（25℃ ）：最小：4小时；最大：28小时
建议涂装方法：刷涂，滚涂
♦ Construction application guidance
Recommended dry film thickness: 200-300um
Coating interval (25℃) : min. : 4 hours; Max: 28 hours
Recommended coating method: brush coating, roll coating
♦施工环境
环境温度：5-35℃
相对湿度：RH%：≤85%
♦ Construction environment
Ambient temperature: 5-35℃
Relative humidity: RH% : ≤85%
♦施工基层处理
金属表面：建议喷砂除锈，达到ISO8501-1或GB8923标准的Sa2.5级。
混凝土表面：达到坚固、密实、平整、干净、干燥状态。不应有起砂、起壳、裂缝、蜂窝麻面等现象。通常需要用腻子修补。
♦ Construction base treatment
Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.
Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena. It usually needs to be repaired with putty.
♦施工注意事项
被涂刷表面要求平整，处理干净，无油、无锈、无灰尘
使用剩余的产品不可倒回原漆桶
本产品为水性涂料，请勿加入有机溶剂或其他涂料使用
♦ Construction precautions
The surface to be brushed should be smooth, clean and free of oil, rust and dust
Do not pour the remaining products back into the original paint bucket
This product is a water-based coating, do not add organic solvents or other coatings
♦产品包装及保质期
包装：10公斤/桶
储存环境温度：5-35℃，产品保质期：12个月（未开封）
确保产品包装密封完好，在阴凉，通风的环境下储存，避免阳光的直射。
♦ Product packaging and shelf life
Packing: 10 kg/barrel
Storage ambient temperature: 5-35℃, product shelf life: 12 months (unopened)
Ensure product packaging is sealed and stored in a cool, ventilated environment, away from direct sunlight.
六、诚信声明Statement of integrity
圣士曼公司承诺以上所列各项产品数据是在相关实验室相对应标准测试获取，测试过程中相关数据会因测试环境和方法不同而结果略有差异。因此圣士曼公司建议客户使用该产品前做好实地考察论证。除产品质量本身外，圣士曼公司不承担任何责任并保证对以上数据进行调整和更新而不提前告知的权利，并请谅解。
The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.