
SSM04 单组份脂肪族防腐防水防护涂层
SSM04 single component aliphatic anti-corrosion and waterproof protective coating
一、产品介绍Product introduction
SSM04单组份脂肪族防腐防水防护涂层是德国Drache Handels UG 公司于二十一
世纪研发的一种单组份脂肪族聚脲防水防腐防护涂层材料,本产品与多种基材都具有优异的附着力。由于脂肪族预聚体独特的化学结构,该产品不但具有卓越的高弹性、高强度、耐磨、抗撞击性能,而且耐腐蚀、耐候性能优异,长期户外使用不粉化、不变色,装饰效果好。
SSM04 single component aliphatic anti-corrosion and waterproof protective coating is made by Drache Handels UGfrom Germany in 21 Century research and development of a single component aliphatic polyurea waterproof anticorrosive protective coating material, this product and a variety of substrates have excellent adhesion. Due to the unique chemical structure of aliphatic prepolymer, the product not only has excellent high elasticity, high strength, wear resistance, impact resistance, but also excellent corrosion resistance, weather resistance, long-term outdoor use without powder, no discoloration, good decorative effect.
二、产品特性Product characteristics
♦ 高固体含量,低VOC排放
♦施工方法简便,可刷涂、滚涂、空气喷涂或高压无气喷涂。
♦良好的耐磨、抗撞击等物理性能
♦优异的防水性能
♦优异的耐化学介质腐蚀性能,可耐一定浓度的酸、碱、盐、油、有机溶剂等
♦卓越的耐老化性能,户外使用不粉化、不变色
♦优异的附着力,可快速牢固的粘结在钢铁、混凝土、木、玻璃纤维等基材的表面
♦使用温度范围宽,可在-50℃~80℃的环境下使用
♦单组份的特性使操作便捷,无需配比,降低了劳动力成本
♦ High solid content, low VOC emissions
♦ The construction method is simple, brush coating, roll coating, air spraying or high pressure airless spraying.
♦ Good wear resistance, impact resistance and other physical properties
♦ Excellent waterproof performance
♦ Excellent corrosion resistance to chemical media, can withstand a certain concentration of acid, alkali, salt, oil, organic solvents, etc
♦ Excellent aging resistance, outdoor use does not powder, does not change color
♦ Excellent adhesion, can be quickly and firmly bonded on the surface of steel, concrete, wood, glass fiber and other substrates
♦ Wide temperature range, can be used in -50℃~80℃ environment
♦ Single component characteristics make the operation convenient, no need to match, reduce labor costs
三、产品应用范围Product application range
石油、化工、交通、建筑、电力、集装箱等行业的户外防水防水防腐防护。如桥梁维护,建筑屋面防水,水利大坝,水电站建筑防水等。
Outdoor waterproof, waterproof and anti-corrosion protection for petroleum, chemical, transportation, construction, power, container and other industries. Such as bridge maintenance, building roof waterproof, water conservancy dam, hydropower station building waterproof and so on.
四、技术参数Technical parameter
1.产品物理属性Physical property of product
项目 |
结果 |
.外观 |
颜色可调 |
比重(g/cm3 ) |
1.2 |
粘度(cps )@20℃ |
500 |
固含量(%) |
75(因不同颜色而略有差异) |
表干时间(小时)@25℃ |
3-5 |
可操作(小时) |
1 |
理论涂布率 |
0.16kg/m2(厚度100um) |
2.典型物理测试性能Typical physical test performance
项目 |
测试标准 |
结果 |
硬度(邵氏A) |
ASTM D-2240 |
82 |
伸长率(%) |
ASTM D-412 |
350 |
拉伸强度(Mpa) |
ASTM D-412 |
28 |
撕裂强度(kN/m) |
ASTM D-624 |
63 |
耐磨测试(750g/500r),mg |
HG/T 3831-2006 |
8 |
附着力(Mpa)钢基材 |
HG/T 3831-2006 |
10 |
附着力(Mpa)混凝土基材 |
HG/T 3831-2006 |
3.5 |
抗冲击性能(kg.m) |
GB/T23446-2009 |
1.0 |
密度(g/cm3) |
GB/T 6750-2007 |
1.2 |
耐人工老化性(1000h) |
GB/T1865-2009 |
无起泡、开裂、生锈、剥落;粉化0级,变色2级,失光2级 |
3.耐腐蚀性能Corrosion resistance
耐酸性10%H2SO4或10%HCl,30d |
无腐蚀,不起泡,不脱落 |
耐碱性10%NaOH, 30d |
无腐蚀,不起泡,不脱落 |
耐盐性10g/L,30d |
无腐蚀,不起泡,不脱落 |
耐盐雾,2000h |
无腐蚀,不起泡,不脱落 |
耐油性0号柴油,原油,30d |
无腐蚀,不起泡,不脱落 |
(仅供参考:需要注意挥发,溅蚀,溢出等影响,如需详细数据,推荐用户自己进行浸泡测试) |
4.产品施工环境Product construction environment
环境温度 |
0~+35℃ |
相对湿度 |
35-85% |
露点 |
≥3℃ |
5. 产品相应固化时间Product curing time
基材温度 |
表干 |
步行强度 |
完全固化 |
+10℃ |
6h |
30h |
7d |
+20℃ |
4h |
24h |
6d |
+30℃ |
3h |
20h |
5d |
注意:固化时间会因环境情况的变化而有所不同,尤其是温度和相对湿度的变化。
Note: Curing times vary depending on environmental conditions, especially temperature and relative humidity.
五、施工注意事项Construction precautions
♦ 产品使用之前,请认真阅读产品使用说明书;
♦施工设备及应用指导
推荐干膜厚度:100-200um(或按设计要求)
覆涂间隔:6-30h,如覆涂时间超过30小时或表面有积灰,建议用砂纸打磨并清洁后再施工
建议涂装方法:无气喷涂,空气喷涂,刷涂,滚涂
♦ 施工基层处理
金属表面:建议喷砂除锈,达到ISO8501-1或GB8923标准的Sa2.5级。
混凝土表面:达到坚固、密实、平整、干净、干燥状态。不应有起砂、起壳、裂缝、蜂窝麻面等现象。通常需要用腻子修补。
木材表面:干净,干燥,没有毛刺,碎片和松散的碎片。
其它材质基层的应用处理可咨询圣士曼技术人员。
♦ 施工注意事项
本产品可在零下10℃的低温情况下使用。如在低温环境使用时,建议先将涂料桶放置在有空调的房间中保持24小时以上。
圣士曼建议每次使用前先将涂料上下搅拌均匀,使用多少、倒出多少,并迅速将桶盖盖紧。使用后的涂料不得再倒回原桶中。
本产品在出厂时已经按需要调整了涂料粘度,施工人员不能私自继续添加稀释剂,如因环境、温度原因粘度发生变化需要调整的,因电话询问供应方,在获得指导认可后方可添加专用稀释剂。
♦产品包装及保质期
包装:10公斤/桶
产品保质期:12个月(自生产日起并未开原包装情况下)
储存环境温度:5℃-32℃
在阴凉、通风的环境下储存,避免阳光直射,远离热源。
♦ Before using the product, please read the product manual carefully;
♦ Construction equipment and application guidance
Recommended dry film thickness: 100-200um (or according to design requirements)
Coating interval: 6-30h, if the coating time exceeds 30 hours or the surface has dust, it is recommended to sand and clean before construction
Recommended coating methods: airless spraying, air spraying, brush coating, roll coating
♦ Construction base treatment
Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.
Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena. It usually needs to be repaired with putty.
Wood surface: clean, dry, free of burrs, chips and loose debris.
The application of other material bases can be consulted by the Saint Seaman technicians.
♦ Construction precautions
This product can be used at a low temperature of minus 10℃. If used in a low temperature environment, it is recommended to place the paint bucket in an air-conditioned room for more than 24 hours.
Mr. Sainthmann recommends mixing the paint up and down before each use, how much to use and how much to pour out, and quickly closing the lid. After use, the paint must not be poured back into the original bucket.
This product has been adjusted according to the needs of the coating viscosity at the factory, the construction personnel can not continue to add diluent without permission, such as due to the environment, temperature changes in viscosity need to be adjusted, because of the phone to ask the supplier, after obtaining guidance approval can add special diluent.
♦ Product packaging and shelf life
Packing: 10kg/barrel
Product shelf life: 12 months (from the date of production without opening the original packaging)
Storage ambient temperature: 5℃-32℃
Store in a cool, ventilated environment away from direct sunlight and away from heat sources.
六、诚信声明
圣士曼公司承诺以上所列各项产品数据是在相关实验室相对应标准测试获取,测试过程中相关数据会因测试环境和方法不同而结果略有差异。因此圣士曼公司建议客户使用该产品前做好实地考察论证。除产品质量本身外,圣士曼公司不承担任何责任并保证对以上数据进行调整和更新而不提前告知的权利,并请谅解。
The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.