咨询热线:13916904730

产品分类

classification

您现在的位置:首页 > 产品展示
SSM06 脂肪族天冬聚脲防腐防护涂层

SSM06 脂肪族天冬聚脲防腐防护涂层

SSM06 aliphatic aspartate polyurea corrosion protection coating


一、 产品介绍product introduction

SSM06 脂肪族天冬聚脲防腐防护涂层是德国Drache Handels UG 公司于二十一

世纪研发的一种选用聚天门冬氨酸酯与多聚异氰酸酯反应聚合而成,因聚天门冬氨酸酯是脂肪族位阻型仲胺,而选用的固化成分为脂肪族多聚异氰酸酯,形成的涂膜具有高保光、保色特性,适合在户外长期使用。当仲胺基团与异氰酸酯基团发生反应时,形成了高交联密度、交叉互穿的高分子链网状结构,也使得本产品具有良好的物理化学特性。

SSM06 aliphatic asparton anticorrosive protective coating is made by Drache Handels UGfrom Germany in 21 Century research and development of a selection of polyaspartic acid ester and polyisocyanate reaction polymerization, because polyaspartic acid ester is aliphatic steric resistance type secondary amine, and the curing component is aliphatic polyisocyanate, the formed film has high light preservation, color preservation characteristics, suitable for long-term use in the outdoors. When the secondary amine group reacts with the isocyanate group, a high crosslinking density and cross-interpenetrating polymer chain network structure is formed, which also makes the product have good physical and chemical properties.

 

二、产品特性Product characteristics

♦ 高固低粘,流平性好,涂层坚韧致密、丰满光亮、色彩鲜艳

♦ 对基层的附着力强,与聚氨酯、环氧等材料有良好配套性

♦ 硬度高、耐划痕性、耐污性好

♦ 优异的耐磨、抗冲击性能性、

♦ 良好的耐腐蚀性能,如酸,碱,盐等

♦ 不变色、不泛黄、不粉化、耐老化,具有卓越的耐候和保光保色性

♦ 可直接应用于金属表面(DTM)的面涂

♦ 本产品不含苯类溶剂和铅类元素,对环境友好。

♦ High solid and low viscosity, good leveling, tough and dense coating, full and bright, bright color

♦ Strong adhesion to the base, good compatibility with polyurethane, epoxy and other materials

♦ High hardness, scratch resistance, good stain resistance

♦ Excellent wear resistance, impact resistance,

♦ Good corrosion resistance, such as acid, alkali, salt, etc

♦ No discoloration, no yellowing, no powder, aging resistance, with excellent weather resistance and light and color preservation

♦ Can be directly applied to metal surface (DTM) coating

♦ This product does not contain benzene solvents and lead elements, and is environmentally friendly.

 

三、产品应用范围Product application range

钢结构、储罐、集装箱、阀门、天然气管道、车架、车轴、货架、槽车、游泳池、污水池、化工围堰等领域的防腐和防护。

Steel structure, storage tanks, containers, valves, natural gas pipelines, frames, axles, shelves, tank cars, swimming pools, sewage ponds, chemical cofferdams and other fields of anti-corrosion and protection.

 

四、技术参数Technical parameter

 

1.产品物理性能Product physical properties

项目

A组分

B组分

外观

浅黄色液体

颜色可调

比重(g/cm³)

1.04

1.50

粘度(cps)@25℃

40-60

100-200

固含量(%)

75

90

混合比例(重量比)

1

2

表干时间h  

1

适用期h    (25℃)

1

理论涂布率(表干膜厚)

0.15kg/㎡ 膜厚100μm

 

2.典型物理测试性能Typical physical test performance  

项目

测试标准

 结果

铅笔硬度

 

H

附着力(Mpa)金属基材

HG/T 3831-2006

9.3

附着力(Mpa)混凝土基材

HG/T 3831-2006

2.8

抗渗性

 

2.1Mpa

弯曲试验(圆柱轴)

 

≤1mm

耐磨性(750g/500r)mg

HG/T 3831-2006

5

冲击强度  kg·cm                

GB/T 1732

50

耐候性人工加速老化2000h

GB/T14522-1993

失光性<1,粉化<1

 

3.耐腐蚀性能Corrosion resistance

耐酸性40%H2SO4或10%HCI,240h 

无腐蚀,不起泡,不脱落

耐碱性40%NaOH,240h

无腐蚀,不起泡,不脱落

耐盐性60g/L, 240h

无腐蚀,不起泡,不脱落

耐盐雾3000h

无腐蚀,不起泡,不脱落

耐油性机油240h  

无腐蚀,不起泡,不脱落

耐水性 48h

无起泡、起皱,不变色,不脱落

(注:以上耐化学介质性能是依据GB/T9274-1988测试法获得,仅供参考。根据挥发,浓度,溢出的不同测试结果也许会略有差异,因此必要情况下,客户独自测试某项指标是有必要的。)

 

4.产品施工环境 Product construction environment

环境温度

0~+35℃

湿度

≤85%

露点

≥3℃

 

5.产品相应固化时间Product curing time

基材温度

表干

步行强度

完全固化

+10℃

2h

12h

7d

+20℃

1.5h

6h

7d

+30℃

1h

4h

7d

注意:固化时间会因环境情况的变化而有所不同,尤其是温度和相对湿度的变化。

Note: Curing times vary depending on environmental conditions, especially temperature and relative humidity.

 

五、施工注意事项construction precautions

♦ 产品使用之前,请认真阅读产品使用说明书;

♦ 手工涂刷、滚刷;空气喷涂,空气压力0.3-0.5Mpa;无气喷涂,喷涂压力15-20Mpa

♦推荐干膜厚度:150-300μm,覆涂间隔:最小1h  最大24h

♦ 施工基层处理:

金属表面:建议喷砂除锈,达到ISO8501-1或GB8923标准的Sa2.5级。

混凝土表面:达到坚固、密实、平整、干净、干燥状态。不应有起砂、起壳、裂缝、蜂窝麻面等现象。通常需要用腻子修补。

木材表面:干净,干燥,没有毛刺,碎片和松散的碎片。

其它材质基层的应用处理可咨询圣士曼技术人员

♦ 施工注意事项:

使用之前,先将B组份充分搅拌均匀。

按要求配比调好,用多少配多少,搅拌均匀后使用,调配好的涂料在1小时内用完。

配漆后,包装桶内的原料必须盖严,防止吸潮。

施工过程中保持干燥清洁,严禁与水、醇、酸、碱等接触。

♦产品包装及保质期

包装:10公斤/桶

储存环境温度:5℃—35℃。产品保质期自生产日起并确保未开封的状态下

A组分:10个月      B组分:10个月

确保产品包装密封完好,在阴凉,通风的环境下储存,避免阳光的直射。

 

♦ Before using the product, please read the product manual carefully;

♦ Manual brushing, rolling brush; Air spraying, air pressure 0.3-0.5Mpa; Airless spraying, spraying pressure 15-20Mpa

♦ Recommended dry film thickness: 150-300μm, coating interval: minimum 1h maximum 24h

♦ Construction base treatment:

Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.

Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena. It usually needs to be repaired with putty.

Wood surface: clean, dry, free of burrs, chips and loose debris.

The application of other material bases can be consulted by the Saint Seaman technicians

♦ Construction precautions:

Before using, mix component B thoroughly.

Adjust according to the required ratio, how much to use, stir evenly after use, the prepared paint is used up within 1 hour.

After painting, the raw materials in the packing bucket must be tightly covered to prevent moisture absorption.

Keep it dry and clean during construction, and do not contact with water, alcohol, acid, alkali, etc.

♦ Product packaging and shelf life

Packing: 10kg/barrel

Storage ambient temperature: 5℃ -35℃. Product shelf life from the date of manufacture and ensure unopened state

Component A: 10 months  Component B: 10 months

Ensure product packaging is sealed and stored in a cool, ventilated environment, away from direct sunlight.

 

六、诚信声明

圣士曼公司承诺以上所列各项产品数据是在相关实验室相对应标准测试获取,测试过程中相关数据会因测试环境和方法不同而结果略有差异。因此圣士曼公司建议客户使用该产品前做好实地考察论证。除产品质量本身外,圣士曼公司不承担任何责任并保证对以上数据进行调整和更新而不提前告知的权利,并请谅解。

The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.