
SSM10高分子改性重防腐涂料
SSM10 polymer modified heavy anticorrosive coating
一、产品介绍Product introduction
SSM10高分子改性重防腐涂料是德国Drache Handels UG 公司于二十一世纪研发的一种以单组份聚氨酯树脂预聚加工合成,成膜涂层致密柔韧,富有弹性。能适应工业企业的各种金属结构在使用过程中受震动、热胀冷缩的轻微变形而不产生裂痕,有效阻止空气、水份、各种腐蚀介质渗入,延缓金属结构发生腐蚀。涂层中存在大量脲键、缩二脲键、氨酯键和氢键,因此具有优异的机械物理性能和防腐蚀性能。
SSM10 polymer modified heavy anticorrosive coating is developed by Drache Handels UG company in the 21st century, which is synthesized by prepolymerization of single-component polyurethane resin. The film coating is dense and flexible. It can adapt to the slight deformation of various metal structures in industrial enterprises during the use of vibration, thermal expansion and cold contraction without cracking, effectively preventing air, water, and various corrosive media from infiltrating, and delaying the corrosion of metal structures. There are a lot of urea bonds, biuret bonds, ammonia ester bonds and hydrogen bonds in the coating, so it has excellent mechanical and physical properties and anti-corrosion properties.
二、产品特性Product characteristics
♦ 优异的附着力,与碳钢、混凝土等基材结合牢固
♦涂层致密柔韧,可抵御循环应力破坏
♦高固体含量,符合环保使用需求
♦优异的机械性能,耐磨、抗撞击、耐刻划
♦优异的防水性能
♦优异的防腐性能,可耐多种化学腐蚀介质侵蚀破坏,如盐雾、酸雨等
♦优良的耐老化性能,户外使用无裂纹、不粉化
♦手涂型涂料,施工便利,可用多种施工操作方式
♦单组份只需搅拌均匀便可涂装,不似多组份涂料因配比不准而易影响质量
♦ Excellent adhesion, firmly combined with carbon steel, concrete and other substrates
♦ The coating is compact and flexible, and can resist cyclic stress damage
♦ High solid content, in line with the needs of environmental protection
♦ Excellent mechanical properties, wear resistance, impact resistance, scratch resistance
♦ Excellent waterproof performance
♦ Excellent anti-corrosion properties, can resist a variety of chemical corrosive media erosion damage, such as salt spray, acid rain, etc
♦ Excellent aging resistance, no crack, no powder for outdoor use
♦ Hand coating, convenient construction, can be used in a variety of construction operations
♦ A single component can be coated only by mixing evenly, unlike multi-component coatings, which are easy to affect the quality due to inaccurate ratio
三、产品应用范围Product application range
该产品广泛应用于石油、化工、交通、建筑、电力等工业企业的防腐防水防护等。
The product is widely used in petroleum, chemical, transportation, construction, electric power and other industrial enterprises anti-corrosion and waterproof protection.
四、技术参数Technical parameter
产品物理属性Physical property of product
项目 |
结果 |
外观 |
颜色可调 |
粘度(cps )@20℃ |
250 |
固含量(%) |
≥65 |
表干时间(小时) |
2-4 |
活化期(小时) |
1 |
理论涂布率 |
0.13kg/m2(厚度100um) |
典型物理测试性能 Typical physical test performance
项目 |
测试标准 |
结果 |
铅笔硬度 |
GB/T 6739-2006 |
2H |
弯曲试验(圆柱轴)mm |
GB/T 6742-1986 |
1 |
抗击穿强度(kv/mm) |
HG/T 3330-1980 |
250 |
耐冲击性(kg·cm) |
GB/T 1732 |
60 |
耐温变性(-40--200℃)24小时 |
GB/9278-1988 |
无异常 |
附着力(Mpa)钢基材 |
ASTM D-3359 |
5A(最高级) |
密度g/cm3 |
GB/T 6750-2007 |
1.03 |
耐腐蚀性能Corrosion resistance
耐酸性50% H2SO4或15%HCl,30d |
无腐蚀,不起泡,不脱落 |
耐碱性50%NaOH, 30d |
无腐蚀,不起泡,不脱落 |
耐盐性50g/L,30d |
无腐蚀,不起泡,不脱落 |
耐盐雾,2000h |
无腐蚀,不起泡,不脱落 |
耐油性0号柴油,原油,30d |
不起泡,不脱落 |
(仅供参考:需要注意挥发、溅蚀、溢出等影响,如需详细数据,推荐用户自己进行浸泡测试) |
产品相应固化时间Product curing time
基材温度 |
表干 |
步行强度 |
完全固化 |
+10℃ |
6h |
24h |
7d |
+20℃ |
3h |
12h |
6d |
+30℃ |
2h |
8h |
5d |
注:以上固化时间会因环境情况的变化而有所不同,尤其是温度和相对湿度的变化。
Note: The above curing time will vary depending on environmental conditions, especially changes in temperature and relative humidity.
五、施工注意事项Construction precautions
♦ 推荐干膜厚度:100-200um(或按设计要求)
♦表面处理:建议喷砂处理达到Sa2.5级以上,或电动工具打磨达到St3级
♦覆涂间隔:2-24h,如覆涂时间超过24小时或表面有积灰,建议用砂纸打磨并清洁后再施工
♦建议涂装方法:无气喷涂,空气喷涂,刷涂,滚涂
♦环境温度:-5 -+35℃,相对湿度:35-85%,露点:金属材质表面施工时必须大于露点温度3℃以上。
♦金属表面:建议喷砂除锈,达到ISO8501-1或GB8923标准的Sa2.5级。
♦混凝土表面:达到坚固、密实、平整、干净、干燥状态。不应有起砂、起壳、裂缝、蜂窝麻面等现象。通常需要用腻子修补。
♦木材表面:干净,干燥,没有毛刺,碎片和松散的碎片。
♦其它材质基层的应用处理可咨询圣士曼技术人员。
♦本产品可在零下10℃的低温情况下使用。如在低温环境使用时,建议先将涂料桶放置在有空调的房间中保持24小时以上。
♦ 圣士曼建议每次使用前先将涂料上下搅拌均匀,使用多少、倒出多少,并迅速将桶盖盖紧。使用后的涂料不得再倒回原桶中。倒出来的涂料须在1小时内用完。
♦本产品在出厂时已经按需要调整了涂料粘度,施工人员不能私自继续添加稀释剂,如因环境、温度原因粘度发生变化需要调整的,应电话询问供应方,在获得指导认可后方可添加指定专用稀释剂。
♦产品保质期:12个月(未开封),储存环境温度:5℃-35℃,请在阴凉、通风的环境下储存,避免阳光直射,远离热源。
♦产品包装:10公斤/桶
♦ Recommended dry film thickness: 100-200um (or according to design requirements)
♦ Surface treatment: It is recommended that sandblasting treatment reach Sa2.5 or above, or power tool grinding reach St3
♦ Coating interval: 2-24h, if the coating time is more than 24 hours or the surface has dust, it is recommended to sand and clean before construction
♦ Recommended coating method: airless spraying, air spraying, brush coating, roll coating
Ambient temperature :-5 -+35℃, relative humidity: 35-85%, dew point: metal surface construction must be greater than the dew point temperature of 3℃ or more.
♦ Metal surface: It is recommended to sand blast to remove rust, to ISO8501-1 or GB8923 standard Sa2.5.
♦ Concrete surface: solid, dense, flat, clean, dry state. There should be no sand, shell, cracks, honeycomb and other phenomena. It usually needs to be repaired with putty.
♦ Wood surface: clean, dry, free of burrs, chips and loose debris.
♦ The application of other material base can consult the technicians of St.
♦ This product can be used at a low temperature of minus 10℃. If used in a low temperature environment, it is recommended to place the paint bucket in an air-conditioned room for more than 24 hours.
♦ St. Schmann recommends mixing the paint up and down before each use, how much to use, how much to pour out, and quickly close the lid. After use, the paint must not be poured back into the original bucket. The poured paint must be used up within one hour.
♦ This product at the factory has been adjusted according to the need to adjust the viscosity of the paint, the construction personnel can not continue to add diluent privately, such as due to the environment, temperature changes in viscosity need to be adjusted, should call the supplier, after obtaining guidance approval can add the designated special diluent.
♦ Shelf life: 12 months (unopened), storage environment temperature: 5℃-35℃, please store in a cool and ventilated environment, avoid direct sunlight, away from heat sources.
♦ Product packaging: 10 kg/barrel
六、诚信声明Statement of good faith
圣士曼公司承诺以上所列各项产品数据是在相关实验室相对应标准测试获取,测试过程中相关数据会因测试环境和方法不同而结果略有差异。因此圣士曼公司建议客户使用该产品前做好实地考察论证。除产品质量本身外,圣士曼公司不承担任何责任并保证对以上数据进行调整和更新而不提前告知的权利,并请谅解。
The company promises that the above listed product data is obtained in the relevant laboratory corresponding to the standard test, and the relevant data will be slightly different due to the different test environment and method. Therefore, the company advises customers to conduct a field study before using the product. In addition to the quality of the product itself, the company does not assume any responsibility and guarantees the right to adjust and update the above data without prior notice.